Skip to main content

Phase 1 Dynamic Mapping With EIGRP

 Phase 1 Dynamic Mapping With EIGRP



Tentu kalian sudah tau, apa yang akan kita bahas pada blogg ini yaitu  Phase 1 Dynamic Mapping With EIGRP... 

Nah Pada lab Sekarang buat routing eigrp pada setiap router baik hub atau spoke untuk menghubungkan jaringan local masing-masing spoke atau hub, dalam hal ini ip loopback akan kita anggap sebagai ip jaringan local kita gaessss.

Dan disini seperti di judul, kita menggunakan routing EIGRP lagi yaa...

Oiya, karena ini adalah lab lanjutan dari lab VPN sebelumnya... soo saya hanya melakukan konfigurasi yang hanya pada lab ini saja, dan jika temen - temen ingin melihat konfigurasi dasarnya dari lab ini... temen - temen bisa lihat di lab - lab sebelumnya... silahkan copy dan paste link dibawah ini..

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html
BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html
BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN




*Oke kita langsung aja ke konfigurasinyaa




TOPOLOGI = 






R1
HUB(config)#int lo 0
HUB(config-if)#ip add 1.1.1.1 255.255.255.255
HUB(config-if)#ex
HUB(config)#
HUB(config)#
HUB(config)#int tu 0
HUB(config-if)#ip nhrp map multi
HUB(config-if)#ip nhrp map multicast dynamic
HUB(config-if)#ex
HUB(config)#
HUB(config)#ro
HUB(config)#router eigrp 12
HUB(config-router)#net 1.1.1.1 0.0.0.0
HUB(config-router)#net 192.168.10.1 0.0.0.0
HUB(config-router)#no au
HUB(config-router)#no auto-summary
HUB(config-router)#exit
HUB(config)#
HUB(config)#int tu 0
HUB(config-if)#no ip split-
HUB(config-if)#no ip split-horizon eigrp 12


R3
Spoke-1(config)#
Spoke-1(config)#int lo 0
Spoke-1(config-if)#ip add 2.2.2.2 255.255.255.255
Spoke-1(config-if)#exit
Spoke-1(config)#
Spoke-1(config)#
Spoke-1(config)#int tu 0
Spoke-1(config-if)#ip nhrp map multicast 12.12.12.1
Spoke-1(config-if)#exit
Spoke-1(config)#ro
Spoke-1(config)#router eigrp 12
Spoke-1(config-router)#net 2.2.2.2 0.0.0.0
Spoke-1(config-router)#netk 192.168.10.2 0.0.0.0
Spoke-1(config-router)#no au
Spoke-1(config-router)#no auto-summary
Spoke-1(config-router)#exit
Spoke-1(config)#


R4
Spoke-2#conf t
Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line.  End with CNTL/Z.
Spoke-2(config)#
Spoke-2(config)#int lo 0
Spoke-2(config-if)#ip add 3.3.3.3 255.255.255.255
Spoke-2(config-if)#ex
Spoke-2(config)#
Spoke-2(config-if)#int tun 0
Spoke-2(config-if)#ip nhrp map multicast 12.12.12.1
Spoke-2(config-if)#exit
Spoke-2(config)#router eigrp 12
Spoke-2(config-router)#net 3.3.3.3 0.0.0.0
Spoke-2(config-router)#net 192.168.10.3 0.0.0.0
Spoke-2(config-router)#no auto-summary
Spoke-2(config-router)#exit
Spoke-2(config)#



Sekarang kita coba pengetesan!!!!.....


R1
HUB(config)#do ping 2.2.2.2 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 50/91/154 ms 


R1
HUB#ping 3.3.3.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 20/55/73 ms


R3
Spoke-1(config)#do ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 52/79/117 ms 


R3
Spoke-1(config)#do ping 3.3.3.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 41/66/157 ms


R4
Spoke-2(config)#do ping 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 73/92/130 ms


R4
Spoke-2(config)#do ping 2.2.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 98/120/177 ms



DONE!!😊😊😊

Comments

Post a Comment

Popular posts from this blog

IP SLA With EEM Script

  IP SLA With EEM Script topologi seperti di gambar EEM dengan IP SLA, yang mana nantinya IP SLA ini digunakan untuk fitur monitoring, jadi jika IP SLA mendetect suatu link down maka EEM akan mengirimkan log ke email kita R1 R1(config)#ip sla 1 R1(config-ip-sla)#icmp-echo 2.2.2.2 R1(config-ip-sla-echo)#frequency 10 R1(config-ip-sla-echo)#exit R1(config)#ip sla schedule 1 life forever start-time now R1(config)#track 1 ip sla 1 reachability Konfigurasi EEM pada R1 R1 R1(config)#event manager applet TRACK_IP_DOWN R1(config-applet)#event track 1 state down R1(config-applet)#action 1.0 syslog msg "IP SLA 1 is down" R1(config-applet)#action 2.0 mail server "smtp.gmail.com" to "idn.id" from "support@idn.id" subject "IP SLA 1 is down" body "IP SLA 1 tidak menerima lagi ICMP packet" R1(config-applet)#exit  R1 R1(config)#event manager applet IP_SLA_1_UP R1(config-applet)#event track 1 state up R1(config-applet)#action 1.0 syslog msg ...
Post a Comment
Read more

Konfigurasi Event CLI

Konfigurasi Event CLI =LAB INI LANJUTAN DARI LAB SEBELUMNYA TOPOLOGI 1 R1(config)#event manager applet SHOW_INTERFACE_UP R1(config-applet)#event cli pattern "show ip interface brief" sync yes R1(config-applet)#action 1.0 cli command "enable" R1(config-applet)#action 2.0 cli command "show ip interface brief | include up" R1(config-applet)#action 3.0 puts "$_cli_result" R1(config-applet)#action 4.0 set $_exit_status "0" SETELAH ITU BISA KALIAN CEK DENGAN DO SH IP INT BR 
Post a Comment
Read more