EIGRP – Konfig Dasar

Lab 1. EIGRP – Konfig Dasar

Konfigurasi ip address pada setiap router seperti berikut ini.

R1(config)#int gigabitEthernet 1/0

R1(config-if)#ip add 12.12.12.1 255.255.255.0

R1(config-if)#no shutdown

R1(config)#int loopback 0

R1(config-if)#ip add 1.1.1.1 255.255.255.255

R1(config-if)#no shutdown

R1(config)#router eigrp 10

R1(config-router)#network 1.1.1.1 0.0.0.0

R1(config-router)#network 12.12.12.1 0.0.0.0

R1(config-router)#no auto-summary

R2(config)#interface gigabitEthernet 1/0

R2(config-if)#ip add 12.12.12.2 255.255.255.0

R2(config-if)#no shutdown

R2(config)#int fastEthernet 0/0

R2(config-if)#ip add 23.23.23.2 255.255.255.0

R2(config-if)#no shutdown

R2(config)#int loopback 0

R2(config-if)#ip add 2.2.2.2 255.255.255.255

R2(config)#router eigrp 10

R2(config-router)#network 2.0.0.0

R2(config-router)#network 12.12.12.2 0.0.0.0

R2(config-router)#network 23.23.23.2 0.0.0.0

R2(config-router)#no auto-summary

R3(config)#int fastEthernet 0/0

R3(config-if)#ip add 23.23.23.3 255.255.255.0

R3(config-if)#no shutdown

R3(config)#int loopback 0

R3(config-if)#ip add 3.3.3.3 255.255.255.255

R3(config)#router eigrp 10

R3(config-router)#network 3.3.3.3 0.0.0.0

R3(config-router)#network 23.23.23.3 0.0.0.0

R3(config-router)#no auto-summary

Cek routing tabel pada Router 1. Pastikan ping ke router lain berhasil.

R1#sh ip route

1.0.0.0/32 is subnetted, 1 subnets

C 1.1.1.1 is directly connected, Loopback0

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/130816] via 12.12.12.2, 00:07:04, GigabitEthernet1/0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/156416] via 12.12.12.2, 00:02:20, GigabitEthernet1/0

23.0.0.0/24 is subnetted, 1 subnets

D 23.23.23.0 [90/28416] via 12.12.12.2, 00:07:04, GigabitEthernet1/0

12.0.0.0/24 is subnetted, 1 subnets

C 12.12.12.0 is directly connected, GigabitEthernet1/0

R1#ping 2.2.2.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/13/28 ms

R1#ping 3.3.3.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 28/32/40 ms

selesai

Comments

Konfigurasi Event OSPF Adjacency (Email)

Konfigurasi Event OSPF Adjacency (Email) LAB INI LANJUTAN SAMA SEPERTI LAB SEBELUM SEBELUMNYA Selain event syslog tadi kita juga bisa memanfaatkan EEM ini untuk mengirimkan informasi ke email kita, misalnya OSPF kita down maka, router kita otomatis akan mengirimkan debug ospf ke email kita. Untuk topology masih sama. KONFIG R1 R1(config)#event manager applet OSPF_DOWN R1(config-applet)#event syslog pattern "Nbr 2.2.2.2 on FastEthernet0/0 from FULL to DOWN" R1(config-applet)#action 1.0 cli command "enable" R1(config-applet)#action 2.0 cli command "debug ip ospf adj" R1(config-applet)#action 3.0 mail server "smtp.gmail.com" to "uuqeili@gmail.com" from "R1@idn.id" subject "OSPF IS DOWN" body "Please fix OSPF" R1(config-applet)#exit Untuk Pengecekkan, kita bisa coba debug aja, dan hapus EEM interface down, Dan kita bisa lihat di email kita apa hasilnyaa... selesai

Remote SPAN ( RSPAN )

Remote SPAN ( RSPAN ) Assalamualaikum temen - temen... kembali lagi di blogg saya, dan terimakasih telah berkunjung ke blogg saya, di blogg kali ini saya akan memberikan materi lab mengenai Remote Span ( RSPAN ). Karena ini adalah blog lanjutan, jadi saya akan mengkonfigurasi yang hanya ada pada blog ini saja, bagi temen - temen ingin melihat konfigurasi sebelumnya ataupun blog sebelumnya mengenai BELAJAR CCNP, bisa cek link dibawah ini : https://bit.ly/37DxJrX TOPOLOGI = SW-1 SW-1(config)#vlan 100 SW-1(config-vlan)#name RSPAN SW-1(config-vlan)#exit SW-1(config)# SW-1(config)#int e0/1 SW-1(config-if)#sw trunk encap dot1q SW-1(config-if)#sw mode tru SW-1(config-if)#exit SW-1(config)# SW-1(config)#monitor session 1 source vlan 10 SW-1(config)#monitor session 1 destination remote vlan 100 SW-2 SW-2(config)#vlan 10 SW-2(config-vlan)#name PC SW-2(config-vlan)#int e0/1 SW-2(config-if)#sw mod acc SW-2(config-if)#sw acc vlan 10 SW-2(config-if)#exit SW-2(config)# SW-2(co...

Konfigurasi Event CLI

Konfigurasi Event CLI =LAB INI LANJUTAN DARI LAB SEBELUMNYA TOPOLOGI 1 R1(config)#event manager applet SHOW_INTERFACE_UP R1(config-applet)#event cli pattern "show ip interface brief" sync yes R1(config-applet)#action 1.0 cli command "enable" R1(config-applet)#action 2.0 cli command "show ip interface brief | include up" R1(config-applet)#action 3.0 puts "$_cli_result" R1(config-applet)#action 4.0 set $_exit_status "0" SETELAH ITU BISA KALIAN CEK DENGAN DO SH IP INT BR

CCNP

Search This Blog