Skip to main content

Etherchannel Mode on

 

Etherchannel Mode on





TOPOLOGI

NAH JADI KETIGA LINK ITU DISATUIN , SEHINGGA BANDWIDTHNYA MENJADI SATU JUGA

KONFIG

SW-1

SW1(config)#interface range e0/0-2

SW1(config-if-range)#channel-group 1 mode on

Creating a port-channel interface Port-channel 1

!

SW1(config)#interface port-channel 1

SW1(config-if)#switchport trunk encapsulation dot1q

SW1(config-if)#switchport mode trunk

SW1(config-if)#ex

SW2(config-if)#switchport mode trunk

SW2(config-if)#exit

Verifikasi

SW-1

SW1#show etherchannel summary

Flags: D - down P - bundled in port-channel

 I - stand-alone s - suspended

 H - Hot-standby (LACP only)

 R - Layer3 S - Layer2

 U - in use N - not in use, no aggregation

 f - failed to allocate aggregator

 M - not in use, minimum links not met

 m - not in use, port not aggregated due to minimum links not met

 u - unsuitable for bundling

 w - waiting to be aggregated

 d - default port

 A - formed by Auto LAG 


Number of channel-groups in use: 1 Number of aggregators: 1

Group Port-channel Protocol Ports

------+-------------+-----------+-------------------------------------------

1 Po1(SU) Et0/0(P) Et0/1(P) Et0/2(P)

SW-1

SW1#show interfaces port-channel 1

switchport Name: Po1

Switchport: Enabled

Administrative Mode: trunk

Operational Mode: trunk

Administrative Trunking Encapsulation: dot1q

Operational Trunking Encapsulation: dot1q

Negotiation of Trunking: On

Access Mode VLAN: 1 (default)

Trunking Native Mode VLAN: 1 (default)

SW-1

SW1#show spanning-tree

 VLAN0001

Spanning tree enabled protocol ieee

Root ID Priority 32769

 Address aabb.cc00.0100

 This bridge is the root

 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

 Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)

 Address aabb.cc00.0100

 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

 Aging Time 300 sec

Interface Role Sts Cost Prio.Nbr Type

------------------- ---- --- --------- -------- ----------------------------

----

Po1 Desg FWD 47 128.65 P2p


SELESAI


Comments

Popular posts from this blog

Phase 1 Dynamic Mapping With EIGRP

  Phase 1 Dynamic  Mapping With EIGRP Tentu kalian sudah tau, apa yang akan kita bahas pada blogg ini yaitu    Phase 1 Dynamic Mapping With EIGRP . ..  Nah Pada lab Sekarang buat routing eigrp pada setiap router baik hub  atau spoke untuk menghubungkan jaringan local masing-masing spoke  atau hub, dalam hal ini ip loopback akan kita anggap sebagai ip jaringan  local kita gaessss. Dan disini seperti di judul, kita menggunakan routing EIGRP lagi yaa... Oiya, karena ini adalah lab lanjutan dari lab VPN sebelumnya... soo saya hanya melakukan konfigurasi yang hanya pada lab ini saja, dan jika temen - temen ingin melihat konfigurasi dasarnya dari lab ini... temen - temen bisa lihat di lab - lab sebelumnya... silahkan copy dan paste link dibawah ini.. 👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN 👉 https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html BELAJ...

Konfigurasi Event CLI

Konfigurasi Event CLI =LAB INI LANJUTAN DARI LAB SEBELUMNYA TOPOLOGI 1 R1(config)#event manager applet SHOW_INTERFACE_UP R1(config-applet)#event cli pattern "show ip interface brief" sync yes R1(config-applet)#action 1.0 cli command "enable" R1(config-applet)#action 2.0 cli command "show ip interface brief | include up" R1(config-applet)#action 3.0 puts "$_cli_result" R1(config-applet)#action 4.0 set $_exit_status "0" SETELAH ITU BISA KALIAN CEK DENGAN DO SH IP INT BR 

Konfigurasi Event OSPF Adjacency (Email)

  Konfigurasi Event OSPF Adjacency (Email) LAB INI LANJUTAN SAMA SEPERTI LAB SEBELUM SEBELUMNYA Selain event syslog tadi kita juga bisa memanfaatkan EEM ini untuk mengirimkan informasi ke email kita, misalnya OSPF kita down maka, router kita otomatis akan mengirimkan debug ospf ke email kita. Untuk topology masih sama. KONFIG R1 R1(config)#event manager applet OSPF_DOWN R1(config-applet)#event syslog pattern "Nbr 2.2.2.2 on FastEthernet0/0 from FULL to DOWN" R1(config-applet)#action 1.0 cli command "enable" R1(config-applet)#action 2.0 cli command "debug ip ospf adj" R1(config-applet)#action 3.0 mail server "smtp.gmail.com" to "uuqeili@gmail.com" from "R1@idn.id" subject "OSPF IS DOWN" body "Please fix OSPF" R1(config-applet)#exit Untuk Pengecekkan, kita bisa coba debug aja,  dan hapus EEM interface down,  Dan kita bisa lihat di email kita apa hasilnyaa... selesai