Skip to main content

OSPF Sumarization – Internal Router

 

OSPF Sumarization – Internal Router



 

ADA 2 CARA :

•Dikonfigurasi pada Router ABR (LSA Type 3)

 •Dikonfigurasi pada Router ASBR (LSA Type 5)

R1

R1(config)#do sh run | section ospf

R1(config)#router ospf 1

R1(config)# router-id 1.1.1.1

R1(config)# redistribute eigrp 10 subnets

R1(config)# network 1.1.1.1 0.0.0.0 area 0

R1(config)#network 12.12.12.1 0.0.0.0 area 0

R1(config)#network 100.100.100.1 0.0.0.0 area 100

R1(config)#network 100.100.100.2 0.0.0.0 area 100

R1(config)#network 100.100.100.3 0.0.0.0 area 100


Hapus terlebih dahulu untuk konfigurasi acl distribute list pada R2


R2

R2(config)#no access-list 1 permit 0.0.0.0 255.255.255.254

R2(config)#router ospf 2

R2(config-router)#no distribute-list 1 in

R2(config-router)#exit


Lalu cek routing tabel pada R3


R3

R3(config)#do sh ip route ospf

 1.0.0.0/32 is subnetted, 1 subnets

O IA 1.1.1.1 [110/3] via 23.23.23.2, 04:10:36, GigabitEthernet1/0

 2.0.0.0/32 is subnetted, 1 subnets

O 2.2.2.2 [110/2] via 23.23.23.2, 04:10:36, GigabitEthernet1/0

 12.0.0.0/24 is subnetted, 1 subnets

O IA 12.12.12.0 [110/2] via 23.23.23.2, 04:10:36, GigabitEthernet1/0

 100.0.0.0/32 is subnetted, 7 subnets

O IA 100.100.100.1 [110/3] via 23.23.23.2, 00:04:13, GigabitEthernet1/0

O IA 100.100.100.2 [110/3] via 23.23.23.2, 04:10:36, GigabitEthernet1/0

O IA 100.100.100.3 [110/3] via 23.23.23.2, 00:04:13, GigabitEthernet1/0

O E2 100.100.100.4 [110/20] via 23.23.23.2, 04:10:26, GigabitEthernet1/0

O E2 100.100.100.5 [110/20] via 23.23.23.2, 04:10:26, GigabitEthernet1/0

O E2 100.100.100.6 [110/20] via 23.23.23.2, 04:10:26, GigabitEthernet1/0

O E2 100.100.100.7 [110/20] via 23.23.23.2, 04:10:26, GigabitEthernet1/0


Konfigurasikan summarization di R1,.


R1

R1(config)#router ospf 1

R1(config-router)#area 100 range 100.100.100.0 255.255.255.248

R1(config-router)#exit


Cek lagi R3 dengan do sh ip route ospf


R3

R3(config)#do sh ip route ospf

 1.0.0.0/32 is subnetted, 1 subnets

O IA 1.1.1.1 [110/3] via 23.23.23.2, 05:05:46, GigabitEthernet1/0

 2.0.0.0/32 is subnetted, 1 subnets

O 2.2.2.2 [110/2] via 23.23.23.2, 05:05:46, GigabitEthernet1/0

 12.0.0.0/24 is subnetted, 1 subnets

O IA 12.12.12.0 [110/2] via 23.23.23.2, 05:05:46, GigabitEthernet1/0

 100.0.0.0/8 is variably subnetted, 5 subnets, 2 masks

O IA 100.100.100.0/29 [110/3] via 23.23.23.2, 00:27:35, GigabitEthernet1/0

O E2 100.100.100.4/32

 [110/20] via 23.23.23.2, 05:05:36, GigabitEthernet1/0

O E2 100.100.100.5/32

 [110/20] via 23.23.23.2, 05:05:36, GigabitEthernet1/0

O E2 100.100.100.6/32

 [110/20] via 23.23.23.2, 05:05:36, GigabitEthernet1/0

O E2 100.100.100.7/32

 [110/20] via 23.23.23.2, 05:05:36, GigabitEthernet1/0


yaa net 100.100.100.0 nya sudah di summary


Cek di R1.

R1

R1(config)#do sh ip ro

 1.0.0.0/32 is subnetted, 1 subnets

C 1.1.1.1 is directly connected, Loopback0

 2.0.0.0/32 is subnetted, 1 subnets

O IA 2.2.2.2 [110/2] via 12.12.12.2, 00:29:19, FastEthernet0/0

 3.0.0.0/32 is subnetted, 1 subnets

O IA 3.3.3.3 [110/3] via 12.12.12.2, 00:29:19, FastEthernet0/0

 12.0.0.0/8 is variably subnetted, 2 subnets, 2 masks

C 12.12.12.0/24 is directly connected, FastEthernet0/0

L 12.12.12.1/32 is directly connected, FastEthernet0/0

 23.0.0.0/24 is subnetted, 1 subnets

O IA 23.23.23.0 [110/2] via 12.12.12.2, 00:29:19, FastEthernet0/0

 33.0.0.0/32 is subnetted, 3 subnets

O E1 33.33.33.1 [110/22] via 12.12.12.2, 00:29:19, FastEthernet0/0

O E1 33.33.33.2 [110/22] via 12.12.12.2, 00:29:19, FastEthernet0/0

O E1 33.33.33.3 [110/22] via 12.12.12.2, 00:29:19, FastEthernet0/0

 100.0.0.0/8 is variably subnetted, 8 subnets, 2 masks

O 100.100.100.0/29 is a summary, 00:29:19, Null0

C 100.100.100.1/32 is directly connected, Loopback1

C 100.100.100.2/32 is directly connected, Loopback2

C 100.100.100.3/32 is directly connected, Loopback3

C 100.100.100.4/32 is directly connected, Loopback4

C 100.100.100.5/32 is directly connected, Loopback5

C 100.100.100.6/32 is directly connected, Loopback6

C 100.100.100.7/32 is directly connected, Loopback7


di OSPF, discard route akan otomatis muncul bila summary route

dikonfigurasikan. itu gunanya untuk menghindari forwarding loop 

nah kita akan hapus sekarang , maka konfigurasi seperti berikut


R1

R1(config)#router ospf 1

R1(config-router)#no discard-route

R1(config-router)#exit

CCNP ENTERPRISE | SMK IDN BOARDING SCHOOL 117

R1

R1(config)#do sh ip route

 1.0.0.0/32 is subnetted, 1 subnets

C 1.1.1.1 is directly connected, Loopback0

 2.0.0.0/32 is subnetted, 1 subnets

O IA 2.2.2.2 [110/2] via 12.12.12.2, 00:17:40, FastEthernet0/0

 3.0.0.0/32 is subnetted, 1 subnets

O IA 3.3.3.3 [110/3] via 12.12.12.2, 00:17:40, FastEthernet0/0

 12.0.0.0/8 is variably subnetted, 2 subnets, 2 masks

C 12.12.12.0/24 is directly connected, FastEthernet0/0

L 12.12.12.1/32 is directly connected, FastEthernet0/0

 23.0.0.0/24 is subnetted, 1 subnets

O IA 23.23.23.0 [110/2] via 12.12.12.2, 00:17:40, FastEthernet0/0

 33.0.0.0/32 is subnetted, 3 subnets

O E1 33.33.33.1 [110/22] via 12.12.12.2, 00:17:40, FastEthernet0/0

O E1 33.33.33.2 [110/22] via 12.12.12.2, 00:17:40, FastEthernet0/0

O E1 33.33.33.3 [110/22] via 12.12.12.2, 00:17:40, FastEthernet0/0

 100.0.0.0/32 is subnetted, 7 subnets

C 100.100.100.1 is directly connected, Loopback1

C 100.100.100.2 is directly connected, Loopback2

C 100.100.100.3 is directly connected, Loopback3

C 100.100.100.4 is directly connected, Loopback4

C 100.100.100.5 is directly connected, Loopback5

C 100.100.100.6 is directly connected, Loopback6

C 100.100.100.7 is directly connected, Loopback7

SELESAI

Comments

Post a Comment

Popular posts from this blog

Konfigurasi Event OSPF Adjacency (Email)

  Konfigurasi Event OSPF Adjacency (Email) LAB INI LANJUTAN SAMA SEPERTI LAB SEBELUM SEBELUMNYA Selain event syslog tadi kita juga bisa memanfaatkan EEM ini untuk mengirimkan informasi ke email kita, misalnya OSPF kita down maka, router kita otomatis akan mengirimkan debug ospf ke email kita. Untuk topology masih sama. KONFIG R1 R1(config)#event manager applet OSPF_DOWN R1(config-applet)#event syslog pattern "Nbr 2.2.2.2 on FastEthernet0/0 from FULL to DOWN" R1(config-applet)#action 1.0 cli command "enable" R1(config-applet)#action 2.0 cli command "debug ip ospf adj" R1(config-applet)#action 3.0 mail server "smtp.gmail.com" to "uuqeili@gmail.com" from "R1@idn.id" subject "OSPF IS DOWN" body "Please fix OSPF" R1(config-applet)#exit Untuk Pengecekkan, kita bisa coba debug aja,  dan hapus EEM interface down,  Dan kita bisa lihat di email kita apa hasilnyaa... selesai
Post a Comment
Read more

Remote SPAN ( RSPAN )

  Remote SPAN  ( RSPAN ) Assalamualaikum temen - temen... kembali lagi di blogg saya, dan terimakasih telah berkunjung ke blogg saya, di blogg kali ini saya akan memberikan materi lab mengenai Remote Span  ( RSPAN ). Karena ini adalah blog lanjutan, jadi saya akan mengkonfigurasi yang hanya ada pada blog ini saja, bagi temen - temen ingin melihat konfigurasi sebelumnya ataupun blog sebelumnya mengenai BELAJAR CCNP, bisa cek link dibawah ini : https://bit.ly/37DxJrX TOPOLOGI =  SW-1 SW-1(config)#vlan 100 SW-1(config-vlan)#name RSPAN SW-1(config-vlan)#exit SW-1(config)# SW-1(config)#int e0/1 SW-1(config-if)#sw trunk encap dot1q SW-1(config-if)#sw mode tru SW-1(config-if)#exit SW-1(config)# SW-1(config)#monitor session 1 source vlan 10 SW-1(config)#monitor session 1 destination remote vlan 100 SW-2 SW-2(config)#vlan 10 SW-2(config-vlan)#name PC SW-2(config-vlan)#int e0/1 SW-2(config-if)#sw mod acc SW-2(config-if)#sw acc vlan 10 SW-2(config-if)#exit SW-2(config)# SW-2(co...
Post a Comment
Read more

Backup config with paramiko

  Backup config with paramiko Backup konfigurasi merupakan pekerjaan yang sangat penting. Agar jika pada saat melakukan konfigurasi terjadi masalah, kita bisa mengembalikan konfigurasi device ke kondisi semula. Tentu saja akan sangat merepotkan jika kita harus melakukan backup konfigurasi pada 100 device. Untuk melakukan pekerjaan tersebut, kita bisa menggunakan python. Ada banyak cara yang bisa kita gunakan untuk backup konfigurasi device menggunakan python, salah satunya menggunakan paramiko. Kita akan mencoba membuat script python menggunakan paramiko untuk backup konfigurasi router. Masih pakai topology dan konfigurasi yang tadi. Ubuntu root@NetworkAutomation-1:~# cp paramiko1.py backup.py root@NetworkAutomation-1:~# nano backup.py root@NetworkAutomation-1:~# cat backup.py import paramiko import time ip_address = "192.168.10.2" username = "cisco" password = "cisco123" ssh_client = paramiko.SSHClient() ssh_client.set_missing_host_key_policy(paramiko.Aut...
Post a Comment
Read more